伊人青青草原_a级毛片免费网站_极品女神白富美露脸啪啪_散兵ちゃんが部下を麻烦_亚洲综合成人精品_安全免动漫网站_日韩4k电影院在线观看全集免费播放_影音先锋吉吉5566_动漫亚洲国产二区精品_欧美日韩一区二区高清

Hello! Shenzhen Win-drive Automation Equipment Co., Ltd. welcomes you!
0755-82113520、13823217507(WeChat)Site map|Legal Notice|Chinese
Case
Case
Current location: Home Case Rack And Pinion Case Robot rack selection case
Robot rack selection case

2022-02-11|admin

Rack and pinion transmission has the characteristics of high speed and high rigidity, so it is widely used in modern mechanical equipment. Common equipment using rack and pinion transmission include: robot seventh axis, truss manipulator, laser cutting machine, woodworking engraving machine and so on.


Next, take the seventh axis of the robot as an example to see how to calculate and select the rack and pinion drive.


The seventh axis of the robot, commonly known as the ground rail, is a walking mechanism used to allow a robot to move back and forth between multiple stations, as shown in the following figure:

機(jī)器人齒條應(yīng)用.png


Usually, the load on the ground rail is heavy and it needs to move at high speed and long distance, so rack and pinion transmission is often used.


The application cases are as follows:


First, you need to determine the relevant parameters of the device:


Drive mode

load weight

Maximum speed

Acceleration

Positioning error

Friction coefficient

Single drive

500KG

60m/min

0.2s

±0.1

0.02

According to the above parameters, the thrust required to accelerate the load can be calculated:

6378018555188519519728323.png

 

Calculate the safety factor (Ka=1.2) and efficiency (96%) to get the actual required thrust:

6378018555189202216499077.png

Here, a helical gear with a modulus of 3 teeth and 20 teeth is selected, and the diameter of the index circle is 63.66, and the maximum torque required for the acceleration of the load is calculated:

6378018555190178813269832.png

The speed of the gear when the load reaches the maximum speed:

6378018555191937314742415.png

Inertia during load movement:

6378018555192522484742415.png

After getting the above parameters, you can start to select the motor and reducer. Here, Siemens 1FL6067 (2kw) is selected. The motor parameters are as follows:

Nominal output torque

Maximum torque

Nominal speed of rotation 

maximum speed

Moment of inertia

9.55Nm

28.7Nm

2000rpm

3000rpm

30.7kg·cm2

In order to ensure that the motor does not exceed the maximum speed of 3000 rpm, the reduction ratio must be less than 10, so we need to choose a reducer with a first-level reduction ratio.


At the same time, the inertia ratio of the load and the motor also needs to be considered. In order to achieve good dynamic performance, it is recommended that the inertia ratio be less than 5 (the maximum cannot exceed 7). According to the formula of the load and motor inertia ratio:


6378018555193694381513170.png

It can be calculated that the reduction ratio is greater than 5, so we finally choose a reduction ratio of 7.


Check:


The maximum speed when the motor is working:


6378018555194573731513170.png

Maximum torque when the motor is working:

6378018555195647537283924.png

Load and Motor Inertia Ratio:

6378018555196526358756507.png

In conclusion, the combination of the motor, reduction ratio and gear can meet the requirements of equipment operation.


When using rack and pinion transmission, the following points should be paid attention to:


1. Try to use pinion gears, which can reduce the diameter of the gear index circle, improve the accuracy, reduce the torque required for the load, and reduce the moment of inertia.


2. Pay attention to the distance between the gear force point and the bearing at the output end of the reducer. If the force arm is too long, it may cause damage to the output shaft of the reducer.


3. In order to reduce noise and improve the stability of equipment operation, limited selection of helical teeth.


4. The end face of the gear needs to be covered with a cover plate to prevent axial play during operation.



Tel: 0755-82113520, 13823217507  
E-mail: sales@sz -windrive. com  
URL: sewdwt.cn com  
Address: room 406, MaoYuan building, No. 9, Songyuan Road, Guiyuan street, Luohu District, Shenzhen  

WeChat

Links
Shenzhen Win-Drive Automation Equipment Co., Ltd.  ALL RIGHT RESERVED 粵ICP備12016317號(hào)